Start from the symptom

Samsung washer won't start or won't unlock.

Two Samsung articles cover this. If the door stays locked or the cycle will not begin, Child Lock, an unfinished cycle, or water still in the tub can be holding the door, and front loaders have an emergency drain hose beside the pump filter. If the washer has no power at all, Samsung lists the cord, a 120V grounded outlet, the breaker and surge protectors.

Last reviewed

Hand gripping the handle of a closed front-load washer door, with wet laundry and suds visible through the glass and lit marks on the panel
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Start with safe observations.

Switch the appliance off and unplug it before any check of your own. Look out for pooled water and jagged debris. Never touch a wet plug or an electrical area, take off a service panel or go past what your model's owner instructions allow.

  1. 1

    Check Child Lock

    On some models, such as front loaders, Child Lock also locks the door.

  2. 2

    Confirm the cycle really finished

    The timer must reach zero and the water must drain. A door lock light means the door is still locked. After a pause, the door stays shut for one minute.

  3. 3

    After a power loss on a top loader

    Samsung says the washer can take up to 5 minutes to unlock and resume.

  4. 4

    Drain the emergency hose on a front loader

    It sits beside the pump filter. When no more water comes out, turn the washer off and on again and the door should unlock.

  5. 5

    Check power

    Cord seated, outlet working (test it with a lamp), the circuit breaker switched off and on, and no surge protector.

  6. 6

    Look at the cord

    Samsung says a damaged power cord is a reason to request service, not to keep using the washer.

Systems a technician may investigate.

Nothing is named as a part until we have tested the washer in place. You see the price and say yes before an order goes in.

Part

Washer supply hoses

Samsung's washer pages name the supply hoses for the not-filling codes, the water-level or leakage group and the hot/cold error. Hot goes to the hot inlet, cold to the cold inlet, and neither hose may be bent or kinked. If a code stays after that, book a technician.

Part

Washer drain hose

The drain hose is the part Samsung's drain guide checks first for the no-drain and overflow codes. It should sit 6 to 8 inches into the standpipe or sink, be secured, and not be kinked. If the code stays after those checks, book a technician.

Part

Washer water supply valves

In its not-filling entry Samsung asks that the water supply valves are completely open, along with the hose checks. A half-open valve can leave a washer short of water. If the code returns with the valves fully open, book a technician.

Part

Washer pump filter

The pump filter is the front loader step in Samsung's drain guide, used for the no-drain codes and for overflow. Top loaders have no removable pump filter. Samsung says a clogged debris filter reduces the effectiveness of the draining system.

Part

Washer door latch

The door latch is the part Samsung's washer door error group points at: the washer does not detect the door as closed and locked. Samsung wants the latch checked as fixed and the door edge clear of laundry. Damage to the door or latch needs a visit.

Part

Washer Add Door

Samsung gives the Add Door its own error, ddC or dC3: the Add Door is not detected as closed and locked. Samsung asks you to check that its latch is fixed and that nothing is caught in it. Damage to the Add Door or its latch needs a visit.

Part

Washer detergent drawer

SDC and 5DC are Samsung's detergent drawer error: the drawer is not completely closed. Samsung says it clicks when fully closed. Push it home until it clicks; if the code lingers, book a technician with us.

Part

Washer motor

Samsung lists a Motor Error under its washer "All other errors": 3C, E3 and 1 3C, and on some models 3E. The entry has a name and no steps. Power the washer off for 2 to 3 minutes and restart; if it continues, book a technician.

Part

Washer Mems sensor

Samsung lists a Mems Sensor Error among its washer "All other errors": 8E, 8C, BC, BE and their numbered forms. For 8E and BE on some models it calls the same entry a Vibration Sensor Error. The entry gives a name and a restart, not a cause.

When observation becomes a service request.

Leave internal testing to a technician.

The door stays locked once the emergency hose runs dry.

The power cord is damaged.

The washer has power and a clear display but will not begin a cycle after Child Lock is off.

The breaker trips again when the washer starts.

Arrange a diagnostic

Sources and model boundaries.

These sources stand behind the Samsung washer won't start or won't unlock advice. Choose the manual that fits your model.

  • Samsung washing machine will not start or fill with water
  • Power issues with Samsung washing machine

Follow the user manual for your exact model. See how we research these pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Why will the door on my Samsung washer not open?

Samsung says the door stays locked while water remains in the drum, and Child Lock can lock it on some models. Let the cycle finish, or empty the emergency drain hose on a front loader.

Where is the emergency drain hose?

Samsung places it beside the pump filter, behind the small panel at the bottom front. Some older front loaders have neither a pump filter nor an emergency hose.

What outlet does a Samsung washer need?

Samsung lists a grounded 120V three-prong outlet on a 20-amp circuit, with no other devices sharing the washer and dryer circuit and no surge protector.

How long can a top loader take to unlock after a power loss?

Samsung says up to 5 minutes. The wait is a safety feature that protects the unit, so give the washer time before you try to force anything.

Let’s take care of it.

Smart appliances still
need a steady hand.