Inside the appliance
Washer supply hoses. In plain English.
Samsung's washer pages name the supply hoses for the not-filling codes, the water-level or leakage group and the hot/cold error. Hot goes to the hot inlet, cold to the cold inlet, and neither hose may be bent or kinked. If a code stays after that, book a technician.

Where it fits.
Washer supply hoses in the appliance
Samsung's pages do not give a position. They name a hot inlet and a cold inlet on the washer.
The picture shows a typical example of this component. It does not tell you which replacement fits your model.
What shifts once this system needs attention.
Washer supply hoses problems can arrive with weaker performance or a code that keeps coming back. A component is tested before anyone decides it is to blame.

Samsung washer leaking
Samsung says most washer leaks come from conditions you can correct: a damaged hose or o-ring, debris under the door gasket, a drain hose set too deep or too shallow, a dirty pump filter, too much detergent, or a washer that rests off level. Water dripping from the door after you open it is normal. A leak with the door closed is not.

Samsung washer not spinning
No spin at all comes from either a drain problem or a motor problem. Samsung says the washer tries to drain before it spins, so a clogged pump filter or a badly set drain hose can stop the spin before it starts. After clearing the drain side, Samsung suggests Calibration mode. If the tub still does not turn, the washer needs service.

Samsung washer won't start or won't unlock
Two Samsung articles cover this. If the door stays locked or the cycle will not begin, Child Lock, an unfinished cycle, or water still in the tub can be holding the door, and front loaders have an emergency drain hose beside the pump filter. If the washer has no power at all, Samsung lists the cord, a 120V grounded outlet, the breaker and surge protectors.
Owner care, within the model instructions.
Switch the appliance off and unplug it before any check of your own. Look out for pooled water and jagged debris. Never touch a wet plug or an electrical area, take off a service panel or go past what your model's owner instructions allow.
- 1
Match the inlets
Samsung says hot goes to the hot inlet and cold to the cold inlet. Swapped hoses are the whole cause of its hot/cold error, and it says that one needs no service.
- 2
Straighten both hoses
The not-filling entry asks that neither hose is bent or kinked. Pull the washer forward only as far as the hoses allow.
- 3
Skip Flood Safe hoses
The not-filling entry carries the line: do not use Flood Safe hoses. Note any hose of that kind before you call us.
Cleaning or replacement?
Leave internal testing to a technician.
The code returns with both hoses seated on the right inlets and running straight.
Water shows around a hose connection or under the washer.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Washer supply hoses advice. Choose the manual that fits your model.
- Samsung washing machine information and error codes
Follow the user manual for your exact model. See how we research these pages.
Which codes point at the supply hoses?
The not-filling group (4C, 4E, nF), the water-level or leakage group (1E, LE, LC) and the hot/cold group (4C2, 4E2, CE, 14C2, nF1).
Can a hot hose problem show on a cold cycle?
Yes. Samsung says an unconnected hot line gives an error when the washer tries to use hot water, even on cycles labeled Cold.
Does the hot/cold error need a visit?
Samsung says service is not needed for it: connect cold to the cold inlet and hot to the hot inlet.
Where do I start?
Read the code, check both hoses for kinks and for the right inlet, then run a cycle. Should the code come back, book us for a visit.
Samsung codes, symptoms, parts, house calls
From the message to what comes next.
1E
1E is listed on Samsung washers as a water level or leakage error: moisture where it does not belong, or a sensor problem. Look for a leak first, then check the hoses and run an empty cycle. Book a technician with us if it persists with no suds.
Samsung washer leaking
Samsung says most washer leaks come from conditions you can correct: a damaged hose or o-ring, debris under the door gasket, a drain hose set too deep or too shallow, a dirty pump filter, too much detergent, or a washer that rests off level. Water dripping from the door after you open it is normal. A leak with the door closed is not.
Washer repair
Book a diagnostic for your exact model, carried out beside the appliance.
Find your metro
Office details, and the access notes to send us.


