Inside the appliance
Washer Mems sensor. In plain English.
Samsung lists a Mems Sensor Error among its washer "All other errors": 8E, 8C, BC, BE and their numbered forms. For 8E and BE on some models it calls the same entry a Vibration Sensor Error. The entry gives a name and a restart, not a cause.

Where it fits.
Washer Mems sensor in the appliance
Samsung's article does not give its position.
The picture shows a typical example of this component. It does not tell you which replacement fits your model.
What shifts once this system needs attention.
Washer Mems sensor problems can arrive with weaker performance or a code that keeps coming back. A component is tested before anyone decides it is to blame.

Samsung washer leaking
Samsung says most washer leaks come from conditions you can correct: a damaged hose or o-ring, debris under the door gasket, a drain hose set too deep or too shallow, a dirty pump filter, too much detergent, or a washer that rests off level. Water dripping from the door after you open it is normal. A leak with the door closed is not.

Samsung washer not spinning
No spin at all comes from either a drain problem or a motor problem. Samsung says the washer tries to drain before it spins, so a clogged pump filter or a badly set drain hose can stop the spin before it starts. After clearing the drain side, Samsung suggests Calibration mode. If the tub still does not turn, the washer needs service.
Owner care, within the model instructions.
Switch the appliance off and unplug it before any check of your own. Look out for pooled water and jagged debris. Never touch a wet plug or an electrical area, take off a service panel or go past what your model's owner instructions allow.
- 1
Restart once
Samsung says to power the washer off for 2 to 3 minutes, power it on and restart the cycle.
- 2
Check BE2 and 8E2
On some models BE2 (8E2) is a Jammed Button Error and on others a Mems Sensor Error. Your user manual decides.
- 3
Note the lights
The Hot & Tap Cold (or Hot & Cool) light pattern is also a Mems Sensor Error in Samsung's lights list.
Cleaning or replacement?
Leave internal testing to a technician.
The code continues after the restart.
The code returns on every cycle.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Washer Mems sensor advice. Choose the manual that fits your model.
- Samsung washing machine information and error codes
Follow the user manual for your exact model. See how we research these pages.
What is a Mems sensor?
Samsung's page does not explain the term. It gives the name Mems Sensor Error and, for 8E and BE on some models, Vibration Sensor Error.
Which strings does this cover?
8E, 8E1, 8E2, BE, BE1, 8C, BC and the numbered 8C, BC, 18C and 1BC forms.
Does Samsung give a cause?
No. It lists the entry by name with the power-off restart and the instruction to request service if it continues.
Is BE2 the same as BE?
Not always. BE2 (8E2) is a Jammed Button Error on some models. Check your user manual.
Samsung codes, symptoms, parts, house calls
From the message to what comes next.
8E
8E appears on Samsung's list of other washer errors as a Mems Sensor Error. Samsung gives the name only, with no specific steps. Power the washer off for 2 to 3 minutes, power it on and restart. Book a technician with us if it continues.
Samsung washer leaking
Samsung says most washer leaks come from conditions you can correct: a damaged hose or o-ring, debris under the door gasket, a drain hose set too deep or too shallow, a dirty pump filter, too much detergent, or a washer that rests off level. Water dripping from the door after you open it is normal. A leak with the door closed is not.
Washer repair
Book a diagnostic for your exact model, carried out beside the appliance.
Find your metro
Office details, and the access notes to send us.

