Start from the symptom
Samsung washer not spinning.
No spin at all comes from either a drain problem or a motor problem. Samsung says the washer tries to drain before it spins, so a clogged pump filter or a badly set drain hose can stop the spin before it starts. After clearing the drain side, Samsung suggests Calibration mode. If the tub still does not turn, the washer needs service.

Start with safe observations.
Switch the appliance off and unplug it before any check of your own. Look out for pooled water and jagged debris. Never touch a wet plug or an electrical area, take off a service panel or go past what your model's owner instructions allow.
- 1
Clean the pump filter
On front loaders, open the lower panel, drain the water into a pan, twist the filter out, brush it, and check the pump impeller behind it. Top loaders have no pump filter.
- 2
Check the drain hose
Look for 6 to 8 inches of insertion, an 18 to 96 inch height, no airtight fit at the standpipe, and no kinks.
- 3
Leave the hose holder in place
Samsung warns that removing the screw and holder on the back can make the washer drain by itself and show LC or 4C.
- 4
Empty the drum, then run Calibration mode
Hold Temp. and Delay End for 3 seconds until Cb shows, then press Start/Pause. The tub rocks for 1 to 3 minutes, shows En, End or 0, and shuts off. Your manual lists the keys if yours differ.
- 5
Note what happens in Calibration
If the tub does not move during calibration, the problem is not a setting. Tell us when you book.
Systems a technician may investigate.
Nothing is named as a part until we have tested the washer in place. You see the price and say yes before an order goes in.

Washer supply hoses
Samsung's washer pages name the supply hoses for the not-filling codes, the water-level or leakage group and the hot/cold error. Hot goes to the hot inlet, cold to the cold inlet, and neither hose may be bent or kinked. If a code stays after that, book a technician.

Washer drain hose
The drain hose is the part Samsung's drain guide checks first for the no-drain and overflow codes. It should sit 6 to 8 inches into the standpipe or sink, be secured, and not be kinked. If the code stays after those checks, book a technician.

Washer water supply valves
In its not-filling entry Samsung asks that the water supply valves are completely open, along with the hose checks. A half-open valve can leave a washer short of water. If the code returns with the valves fully open, book a technician.

Washer pump filter
The pump filter is the front loader step in Samsung's drain guide, used for the no-drain codes and for overflow. Top loaders have no removable pump filter. Samsung says a clogged debris filter reduces the effectiveness of the draining system.

Washer door latch
The door latch is the part Samsung's washer door error group points at: the washer does not detect the door as closed and locked. Samsung wants the latch checked as fixed and the door edge clear of laundry. Damage to the door or latch needs a visit.

Washer Add Door
Samsung gives the Add Door its own error, ddC or dC3: the Add Door is not detected as closed and locked. Samsung asks you to check that its latch is fixed and that nothing is caught in it. Damage to the Add Door or its latch needs a visit.

Washer detergent drawer
SDC and 5DC are Samsung's detergent drawer error: the drawer is not completely closed. Samsung says it clicks when fully closed. Push it home until it clicks; if the code lingers, book a technician with us.

Washer motor
Samsung lists a Motor Error under its washer "All other errors": 3C, E3 and 1 3C, and on some models 3E. The entry has a name and no steps. Power the washer off for 2 to 3 minutes and restart; if it continues, book a technician.

Washer Mems sensor
Samsung lists a Mems Sensor Error among its washer "All other errors": 8E, 8C, BC, BE and their numbered forms. For 8E and BE on some models it calls the same entry a Vibration Sensor Error. The entry gives a name and a restart, not a cause.
If the display adds a code.
Information
Cb is Samsung's Calibration mode on a washer, not an error. It recalibrates weight detection, runs the drum back and forth for 1 to 3 minutes and ends by itself. The washer must be empty for it to calibrate.
Water and drain
5C is Samsung's no-drain error on a washer: water is not draining at the right speed, or at all. Samsung points to its drain guide: level washer, drain hose 6 to 8 inches into the pipe and not kinked, pump filter on front loaders.
Water and drain
LC is listed on Samsung washers as a water level or leakage error: moisture where it does not belong, or a sensor problem. Look for a leak first, then check the hoses and run an empty cycle. Book a technician with us if it persists with no suds.
Read the related care guide.

Samsung panel or door will not respond? Check Child Lock.
Child Lock disables the panel buttons on a Samsung washer or dryer except a few, such as Power. To turn it off, press and hold the two Child Lock buttons together until the icon goes out; on models with Temporary off, hold them once so it flashes, then again. Restarting the machine will not clear it. [1][2]

Cb on your Samsung washer display? It is Calibration mode.
Calibration mode recalibrates a Samsung washer's weight detection, which sets the water used per cycle. Run it empty, after installation, after you move or adjust the washer, or when water amounts seem wrong. On many models, hold Temp. and Delay End for 3 seconds to show Cb, then press Start/Pause. [1][2]
When observation becomes a service request.
Leave internal testing to a technician.
The tub stays still during Calibration mode.
Filter and hose are in order, yet the tub never turns.
The drain hose holder is missing.
The washer spun before and stopped mid-cycle. Samsung treats that as a separate spin problem.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Samsung washer not spinning advice. Choose the manual that fits your model.
- Samsung washing machine does not spin at all
Follow the user manual for your exact model. See how we research these pages.
Why does a clogged drain stop my washer from spinning?
Samsung says the washer drains before it spins. If water cannot leave, it never moves on to the spin step. That is why Samsung starts the checks at the pump filter and drain hose.
What is Cb on my washer display?
Cb means Calibration mode is running. The tub turns back and forth for 1 to 3 minutes while the washer relearns its weight detection, then it shows En, End or 0 and turns off.
Does my washer have a pump filter?
Only front loaders do, and some older ones have none. If your washer is a top loader or has no filter panel, skip that step and go to the drain hose check.
What if the washer spun before and now stops partway?
Samsung splits that case from a washer that never spins. Mid-cycle stops, slow spins and spin codes sit in its separate spin guide, which we have not summarized here.
Samsung codes, symptoms, parts, house calls
From the message to what comes next.
Cb
Cb is Samsung's Calibration mode on a washer, not an error. It recalibrates weight detection, runs the drum back and forth for 1 to 3 minutes and ends by itself. The washer must be empty for it to calibrate.
Samsung washer leaking
Samsung says most washer leaks come from conditions you can correct: a damaged hose or o-ring, debris under the door gasket, a drain hose set too deep or too shallow, a dirty pump filter, too much detergent, or a washer that rests off level. Water dripping from the door after you open it is normal. A leak with the door closed is not.
Washer repair
Book a diagnostic for your exact model, carried out beside the appliance.
Find your metro
Office details, and the access notes to send us.