Samsung washer 1C / Water and drain

Samsung washer
error 1C

Washer / display reference1C

1C is listed on Samsung washers as a water level or leakage error: moisture where it does not belong, or a sensor problem. Look for a leak first, then check the hoses and run an empty cycle. Book a technician with us if it persists with no suds.

Also shown as 1C

Last reviewed

Washer / display reference1C
Meaning
1C is listed on Samsung washers as a water level or leakage error: moisture where it does not belong, or a sensor problem. Look for a leak first, then check the hoses and run an empty cycle. Book a technician with us if it persists with no suds.
Who handles it
Technician — close the water supply
Related codes
Source
Samsung washing machine information and error codes

What Samsung washer 1C means.

What it means

1C is listed on Samsung washers as a water level or leakage error: moisture where it does not belong, or a sensor problem. Look for a leak first, then check the hoses and run an empty cycle. Book a technician with us if it persists with no suds.

What you can safely check

Before you look behind a panel, pull the plug and shut both water taps, and mop up any puddle you find.

When to call a technician

No suds show up during the empty cycle and 1C still comes back.

Your Samsung checks, remembered on this device

Safe checks, in order.

0 of 4 checks done
  1. Samsung washer 1C: Gloved hand holding a washer's drain pump filter with lint beside the open lower access door, with a shallow tray of water on a towel
    Illustration. Follow your model’s instructions.
    Before you begin

    Read the display

    Compare the display with 1C one character at a time: Samsung writes it with the digit 1 and a capital C.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Look for a leak

    Check the floor, the hose connections and the back of the washer for water, including very small drips.

  3. A washer control panel with a short code lit on the screen
    Illustration. Follow your model’s instructions.
    Check 3

    Check the hoses

    Make sure the supply hoses and the drain hose are not kinked. Leave the screw that holds the drain hose to the back panel in place; if the holder is missing, the washer needs service.

  4. Over a technician's shoulder, hands hold a tablet showing an empty checklist with boxes, a front-loading washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Run an empty cycle

    Run a cycle with no detergent or softener and watch for suds. Suds mean too much detergent or a non-HE detergent; repeat empty cycles until they stop, then see whether the code returns.

Still showing 1C?

Tell us your model and the checks you have already run, then open your request from this spot.

Book a visit

Fill and the water level.

Conceptual Washer sectionInlet valveTubLevel sensorDrain pump1234
  1. 2Tub

This is a sketch, because the inside of a Samsung changes from model to model. Tap an outlined part for its photo and the matching check.

Parts behind the message.

Two braided steel hoses run from wall shutoff valves to the back of a washer, with red and blue bands on the hoses

Component reference

Washer supply hoses

Samsung's washer pages name the supply hoses for the not-filling codes, the water-level or leakage group and the hot/cold error.

Read the definition
Gray corrugated drain hose curved into a white standpipe with a hand holding a yellow tape measure against the hose

Component reference

Washer drain hose

The drain hose is the part Samsung's drain guide checks first for the no-drain and overflow codes.

Read the definition
Hand shining a flashlight beside a front-load washer toward its drain and braided supply hoses, with water on the floor

Component reference

Washer water level sensor

On a Samsung washer, the water level sensor is named in one error entry: 1E, LE, 1C, LC, LC1, 1 1C and 1 LC, "Water level or leakage error".

Read the definition

A little more context.

What is a Samsung washer reporting with 1C?

Samsung describes it as moisture detected somewhere it does not belong, or a problem with the sensor itself. Small leaks can go unnoticed, and fixing a leak clears the code.

Read the supporting manual

What should I check before I book a visit?

Look for a leak, however small. Check that the supply hoses and the drain hose behind the washer are not kinked. Then run an empty cycle with no additives and watch for suds.

Read the supporting manual

Can the washer stay in use while this shows?

Pull the plug and shut both taps before you look behind the washer, and mop up any water first. If you find a leak, stop using the washer until it is fixed.

Read the supporting manual

How is 1C different from the codes near it?

On a small display the 1 in 1C can be taken for I or l. Samsung's washer list has no row spelled that way, so 1C is the reading to look up.

Read the supporting manual

The manual behind the message.

Manufacturer document

Samsung washing machine information and error codes

Samsung Electronics America (official US support article, samsung.com/us)

page meta date 2026-06-09 (latest of three page dates: 2024-09-04, 2026-05-05, 2026-06-09); no printed revision / article

Scope: Samsung washers, all models unless the article notes otherwise. Source: Samsung washing machine information and error codes (Samsung US support article TSG10000997), checked November 2026. The entry used for 1C is printed as: "1E, LE, 1C, LC, LC1, 1 1C, 1 LC: Water level or leakage error" (TSG10000997, web article).

Here to help

Good questions.
Clear answers.

Talk to our team
What is a Samsung washer reporting with 1C?

Samsung describes it as moisture detected somewhere it does not belong, or a problem with the sensor itself. Small leaks can go unnoticed, and fixing a leak clears the code.

Can too much detergent cause this code?

Yes, on Samsung's list. Suds during an empty cycle point to too much detergent or a non-HE detergent. Repeat empty cycles until the suds stop, then see whether the code comes back.

What if I find the screw on the drain hose is missing?

Samsung says to put the screw and holder back with any screw that fits. If the holder itself is missing, the washer needs service.

Can 1C be misread on the display?

On a small display the 1 in 1C can be taken for I or l. Samsung's washer list has no row spelled that way, so 1C is the reading to look up.

Do I need a visit for 1C?

Samsung's article sends you to service only when no suds appear in the empty cycle and the code continues. That is the point to book a visit with us.

Which other strings does Samsung print with it?

Samsung's line for Water level or leakage error prints 7 strings in this order: 1E, LE, 1C, LC, LC1, 1 1C, 1 LC. 1C is number 3 of them.

Let’s take care of it.

Smart appliances still
need a steady hand.