Start from the symptom
Samsung washer detergent dispenser problems.
When additives drain out of the drawer at once or the drawer ends the cycle full of water, Samsung points to six things: going over a MAX line, a missing liquid insert, an auto dispenser that is still off, a washer standing off level, a dirty drawer, or thick softener. Use HE detergent and run empty rinse cycles to flush the siphons.

Start with safe observations.
Switch the appliance off and unplug it before any check of your own. Look out for pooled water and jagged debris. Never touch a wet plug or an electrical area, take off a service panel or go past what your model's owner instructions allow.
- 1
Stay under the MAX line
Each compartment has one. A liquid added without its insert, or past the line, drains straight into the tub.
- 2
Match the insert to the detergent
Liquid detergent needs the liquid insert pressed fully down. Some models also have a bleach insert.
- 3
Turn on the auto dispenser
Auto dispenser compartments take liquid only. In the options menu, switch on Dose per Wash and Dose per Rinse. They default to off after shipping or a power outage over 5 minutes.
- 4
Level the washer
Off-level feet tilt the drawer and upsets how the siphons work.
- 5
Clean the drawer
On a front loader, press both side ends in and pull. On a top loader, pull it out and tip it up. Lumpy softener can be thinned with warm water, still under the MAX line.
- 6
Flush with empty cycles
Run Rinse+Spin with no detergent. If bubbles show, residue is leaving the system, so keep running cycles until they stop.
Systems a technician may investigate.
Nothing is named as a part until we have tested the washer in place. You see the price and say yes before an order goes in.

Washer supply hoses
Samsung's washer pages name the supply hoses for the not-filling codes, the water-level or leakage group and the hot/cold error. Hot goes to the hot inlet, cold to the cold inlet, and neither hose may be bent or kinked. If a code stays after that, book a technician.

Washer drain hose
The drain hose is the part Samsung's drain guide checks first for the no-drain and overflow codes. It should sit 6 to 8 inches into the standpipe or sink, be secured, and not be kinked. If the code stays after those checks, book a technician.

Washer water supply valves
In its not-filling entry Samsung asks that the water supply valves are completely open, along with the hose checks. A half-open valve can leave a washer short of water. If the code returns with the valves fully open, book a technician.

Washer pump filter
The pump filter is the front loader step in Samsung's drain guide, used for the no-drain codes and for overflow. Top loaders have no removable pump filter. Samsung says a clogged debris filter reduces the effectiveness of the draining system.

Washer door latch
The door latch is the part Samsung's washer door error group points at: the washer does not detect the door as closed and locked. Samsung wants the latch checked as fixed and the door edge clear of laundry. Damage to the door or latch needs a visit.

Washer Add Door
Samsung gives the Add Door its own error, ddC or dC3: the Add Door is not detected as closed and locked. Samsung asks you to check that its latch is fixed and that nothing is caught in it. Damage to the Add Door or its latch needs a visit.

Washer detergent drawer
SDC and 5DC are Samsung's detergent drawer error: the drawer is not completely closed. Samsung says it clicks when fully closed. Push it home until it clicks; if the code lingers, book a technician with us.

Washer motor
Samsung lists a Motor Error under its washer "All other errors": 3C, E3 and 1 3C, and on some models 3E. The entry has a name and no steps. Power the washer off for 2 to 3 minutes and restart; if it continues, book a technician.

Washer Mems sensor
Samsung lists a Mems Sensor Error among its washer "All other errors": 8E, 8C, BC, BE and their numbered forms. For 8E and BE on some models it calls the same entry a Vibration Sensor Error. The entry gives a name and a restart, not a cause.
If the display adds a code.
Door and lid
SDC is Samsung's detergent drawer error on a washer: the drawer is not completely closed. Push it in until it clicks. Book a technician with us if it still shows with the drawer fully closed.
Information
SUd is Samsung's excessive-suds code on a washer: the washer detected over-sudsing and paused to let the suds settle. It continues by itself and needs no service. Samsung ties it to incorrect detergent use.
Read the related care guide.

Samsung panel or door will not respond? Check Child Lock.
Child Lock disables the panel buttons on a Samsung washer or dryer except a few, such as Power. To turn it off, press and hold the two Child Lock buttons together until the icon goes out; on models with Temporary off, hold them once so it flashes, then again. Restarting the machine will not clear it. [1][2]

Cb on your Samsung washer display? It is Calibration mode.
Calibration mode recalibrates a Samsung washer's weight detection, which sets the water used per cycle. Run it empty, after installation, after you move or adjust the washer, or when water amounts seem wrong. On many models, hold Temp. and Delay End for 3 seconds to show Cb, then press Start/Pause. [1][2]
When observation becomes a service request.
Leave internal testing to a technician.
The drawer is clean, level, within MAX and the problem remains.
Additives still drain immediately with a new drawer in place.
A leak comes from the drawer area itself.
The drawer will not close all the way.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Samsung washer detergent dispenser problems advice. Choose the manual that fits your model.
- Dispenser drawer issues in Samsung washing machine
Follow the user manual for your exact model. See how we research these pages.
Why did my detergent go straight into the tub?
Samsung says going over a compartment's MAX line, or pouring liquid in without its insert, makes the additive drain into the tub right away. That can stain clothes and build residue.
Why is the auto dispenser not dosing?
Auto dispenser compartments are off by default after shipping and after a power outage longer than 5 minutes. Turn on Dose per Wash and Dose per Rinse in the options menu.
Can I put powder in an auto dispenser compartment?
No. Samsung says the Auto Detergent and Auto Softener compartments work with liquid only. Use the manual drawer for powder, and remove the liquid tray first.
What does SDC mean?
SDC means the detergent drawer is not fully closed. Samsung says the drawer clicks when it is seated. Push it in until it clicks and restart.
Samsung codes, symptoms, parts, house calls
From the message to what comes next.
SDC
SDC is Samsung's detergent drawer error on a washer: the drawer is not completely closed. Push it in until it clicks. Book a technician with us if it still shows with the drawer fully closed.
Samsung washer leaking
Samsung says most washer leaks come from conditions you can correct: a damaged hose or o-ring, debris under the door gasket, a drain hose set too deep or too shallow, a dirty pump filter, too much detergent, or a washer that rests off level. Water dripping from the door after you open it is normal. A leak with the door closed is not.
Washer repair
Book a diagnostic for your exact model, carried out beside the appliance.
Find your metro
Office details, and the access notes to send us.