Samsung washer BC / Sensors

Samsung washer
error BC

Washer / display referenceBC

BC appears on Samsung's list of other washer errors as a Mems Sensor Error. Samsung gives the name only, with no specific steps. Power the washer off for 2 to 3 minutes, power it on and restart. Book a technician with us if it continues.

Also shown as BC

Last reviewed

Washer / display referenceBC
Meaning
BC appears on Samsung's list of other washer errors as a Mems Sensor Error. Samsung gives the name only, with no specific steps. Power the washer off for 2 to 3 minutes, power it on and restart. Book a technician with us if it continues.
Who handles it
Reset, then book
Related codes
Source
Samsung washing machine information and error codes

What Samsung washer BC means.

What it means

BC appears on Samsung's list of other washer errors as a Mems Sensor Error. Samsung gives the name only, with no specific steps. Power the washer off for 2 to 3 minutes, power it on and restart. Book a technician with us if it continues.

What you can safely check

Before you look behind a panel, pull the plug and shut both water taps, and mop up any puddle you find.

When to call a technician

BC returns after the power-off and restart.

Your Samsung checks, remembered on this device

Safe checks, in order.

0 of 4 checks done
  1. Samsung washer BC: Hand holding a small round sensor on a short wire harness beside the tub of a washer with its front panel off and the plug lying on the counter
    Illustration. Follow your model’s instructions.
    Before you begin

    Read the display

    Compare the display with BC one character at a time: Samsung writes it with a capital B and a capital C.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Power off for 2 to 3 minutes

    Turn the washer off and leave it for 2 to 3 minutes.

  3. A washer control panel with a short code lit on the screen
    Illustration. Follow your model’s instructions.
    Check 3

    Power on and restart

    Turn it back on and restart the cycle.

  4. Over a technician's shoulder, hands hold a tablet showing an empty checklist with boxes, a front-loading washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Note when it appears

    Write down whether it appeared at the start or during a spin.

Still showing BC?

Tell us your model and the checks you have already run, then open your request from this spot.

Book a visit

The control and its sensors.

Conceptual Washer sectionControl panelControl boardLevel sensorMotor wiring1234
  1. 1Control panel
  2. 2Control board
  3. 4Motor wiring

This is a sketch, because the inside of a Samsung changes from model to model. Tap an outlined part for its photo and the matching check.

Parts behind the message.

Gloved hand holding a small green circuit board with a sensor chip beside an open washer control housing with wiring

Component reference

Washer Mems sensor

Samsung lists a Mems Sensor Error among its washer "All other errors": 8E, 8C, BC, BE and their numbered forms.

Read the definition

A little more context.

What is a Samsung washer reporting with BC?

For BC, Samsung lists it in "All other errors" as a Mems Sensor Error, and gives no specific steps for it, only the basic power-cycle steps.

Read the supporting manual

What should I check before I book a visit?

Power the washer off for 2 to 3 minutes, power it back on and restart the cycle. If the code comes back, note what the washer was doing when it appeared.

Read the supporting manual

Can the washer stay in use while this shows?

Treat a repeating Mems sensor error as a service matter. Unplug the washer before you open any panel, and do not bypass any part.

Read the supporting manual

How is BC different from the codes near it?

8C differs from BC only by a look-alike character, B against 8. Samsung lists both under Mems Sensor Error, so they carry the same meaning.

Read the supporting manual

The manual behind the message.

Manufacturer document

Samsung washing machine information and error codes

Samsung Electronics America (official US support article, samsung.com/us)

page meta date 2026-06-09 (latest of three page dates: 2024-09-04, 2026-05-05, 2026-06-09); no printed revision / article

Scope: Samsung washers, all models unless the article notes otherwise. Source: Samsung washing machine information and error codes (Samsung US support article TSG10000997), checked November 2026. The entry used for BC is printed as: "8E, 8E1, 8E2, BE, BE1, BE2, 8C, BC, 8C1, 8C2, BC1, BC2, 1 8C, 1 BC, 18C1, 1BC1, 18C2, 1BC2 - Mems Sensor Error" (TSG10000997, web article).

Here to help

Good questions.
Clear answers.

Talk to our team
What is a Samsung washer reporting with BC?

Samsung lists it in "All other errors" as a Mems Sensor Error, and gives no specific steps for it, only the basic power-cycle steps.

Does Samsung give specific steps for this code?

No. It is in the "All other errors" part of the list, where the basic power-off, power-on and restart steps apply.

Is BC the same as 8C?

8C differs from BC only by a look-alike character, B against 8. Samsung lists both under Mems Sensor Error, so they carry the same meaning.

Do I need a visit for BC?

Samsung says to request service if the error continues after the basic steps. Book a visit with us at that point.

Which other strings does Samsung print with it?

Samsung's line for Mems Sensor Error prints 18 strings, and BC is number 8, right after 8C and right before 8C1.

Let’s take care of it.

Smart appliances still
need a steady hand.