What it means
OE is Samsung's overflow error on a washer: there is too much water in the tub. Samsung sends you to the same drain guide as for no-drain codes. Check the drain hose and level, and book a technician with us if it continues.
Samsung washer OE / Water and drain
OE is Samsung's overflow error on a washer: there is too much water in the tub. Samsung sends you to the same drain guide as for no-drain codes. Check the drain hose and level, and book a technician with us if it continues.
Also shown as OE
OE is Samsung's overflow error on a washer: there is too much water in the tub. Samsung sends you to the same drain guide as for no-drain codes. Check the drain hose and level, and book a technician with us if it continues.
Before you look behind a panel, pull the plug and shut both water taps, and mop up any puddle you find.
The water level stays too high after the drain checks.
Your Samsung checks, remembered on this device

Compare the display with OE one character at a time: Samsung writes it with a capital O and a capital E.

Turn the washer off and unplug it if water is standing in the tub or the door area.

The drain hose should be unkinked and 6 to 8 inches into the pipe; the pump filter on a front loader should be clear.

Make sure both water taps are not leaking by into the washer while it is off.
Tell us your model and the checks you have already run, then open your request from this spot.
Book a visit

This is a sketch, because the inside of a Samsung changes from model to model. Tap an outlined part for its photo and the matching check.

Component reference
The drain hose is the part Samsung's drain guide checks first for the no-drain and overflow codes.
Read the definition
Component reference
The pump filter is the front loader step in Samsung's drain guide, used for the no-drain codes and for overflow.
Read the definitionFor OE, Samsung says there is too much water in the washer and refers to the same guide it uses for water that will not drain.
Read the supporting manualWith OE showing, do not start another cycle on top of standing water. Check the drain hose, the level of the washer and, on a front loader, the pump filter.
Read the supporting manualSafety with OE: Too much water can reach electrical parts and can flood the floor. Unplug the washer, shut the taps and remove water before you inspect anything.
Read the supporting manual0E differs from OE only by a look-alike character, O against 0. Samsung lists both under Overflow error, so they carry the same meaning. The same characters also appear on a dishwasher, where Samsung ties it to Over-level water error. Check which appliance you are standing in front of.
Read the supporting manualManufacturer document
Samsung Electronics America (official US support article, samsung.com/us)
page meta date 2026-06-09 (latest of three page dates: 2024-09-04, 2026-05-05, 2026-06-09); no printed revision / article
Manufacturer document
Samsung Electronics America (official US support article, samsung.com/us)
page meta date 2026-05-05; no printed revision / article
Scope: Samsung washers, all models unless the article notes otherwise. Source: Samsung washing machine information and error codes; Samsung washing machine will not drain (Samsung US support article TSG10000997, TSG10007110), checked November 2026. The entry used for OE is printed as: "OE, 0E, OC, 0C, 1 OC, 1 0C: Overflow error" (TSG10000997, web article).
Samsung says there is too much water in the washer and refers to the same guide it uses for water that will not drain.
No. Samsung groups overflow separately from the water level or leakage codes: one means too much water in the tub, the other moisture where it does not belong.
Both use the same drain guide, because water that cannot leave the tub is the usual way the level climbs.
0E differs from OE only by a look-alike character, O against 0. Samsung lists both under Overflow error, so they carry the same meaning.
If the drain path is clear and the washer still reports too much water, book a visit with us before running it again.
Samsung's line for Overflow error prints 6 strings in this order: OE, 0E, OC, 0C, 1 OC, 1 0C. OE is number 1 of them.
Samsung codes, symptoms, parts, house calls
0E is Samsung's overflow error on a washer: there is too much water in the tub. Samsung sends you to the same drain guide as for no-drain codes. Check the drain hose and level, and book a technician with us if it continues.
Samsung says most washer leaks come from conditions you can correct: a damaged hose or o-ring, debris under the door gasket, a drain hose set too deep or too shallow, a dirty pump filter, too much detergent, or a washer that rests off level. Water dripping from the door after you open it is normal. A leak with the door closed is not.
The drain hose is the part Samsung's drain guide checks first for the no-drain and overflow codes. It should sit 6 to 8 inches into the standpipe or sink, be secured, and not be kinked. If the code stays after those checks, book a technician.
Book a diagnostic for your exact model, carried out beside the appliance.
Office details, and the access notes to send us.