Troubleshooting

Drum turning, no heat the order Samsung checks it in

A Samsung dryer with no heat gets checked in a fixed order: look for an error code, rule out a heat-free cycle setting, confirm it is truly cold with a 30-second Time Dry test, then review the 240 V outlet, cycle the breaker, run the vent test and inspect the vent. If all pass, it is a repair. [1]

Hand held flat inside the empty stainless drum of an open dryer to feel for warmth, with a wall outlet and towels behind
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • Confirm it is truly cold: Time Dry, Eco Dry off, 30 seconds, hand inside. 1
  • An electric dryer has two circuits, and one can trip alone, leaving the drum spinning without a heater. 1
  • A dryer that has never heated since installation points at installation first. 1
  • A vent blockage test that passes, with still no heat, is the point where Samsung says to request service. 1

What counts as no heat on a Samsung dryer?#

It means the drum turns and the controls work, but the air inside never warms, even on a cycle meant to heat. Samsung's article says the steps apply even if only one cycle shows the trouble, as long as that cycle is supposed to heat. 1

Before anything else, look at the display. Samsung's no-heat path begins by asking whether an error code is showing, because a code can mean service is needed and nothing else on the list is worth doing. 1 The dryer code pages here begin with HC and 9C1, both of which can appear when heating trouble is in play. 3

How do I check the dryer is really cold?#

Run Time Dry with Eco Dry turned off, wait 30 seconds, open the door and put your hand in the drum. Any warmth at all means the dryer heats a little, and Samsung then moves you to the not-hot-enough steps. 1

This quick test also stops you from chasing the wrong problem. Eco Dry deliberately begins part of a cycle with no hot air, so a cool drum in the first minutes of an Eco Dry cycle is expected. 1 The steps below are for the case where Time Dry with Eco Dry off stays cold. If you want the Eco Dry details, see our Eco Dry and Sensor Dry guide.

  1. 1

    Look for an error code#

    A code on the display may mean service and no other check applies. 1

  2. 2

    Set Time Dry and turn Eco Dry off#

    Start the cycle on the setting you want to test. 1

  3. 3

    Wait 30 seconds, then open the door#

    Put your hand in the drum and feel for warmth. 1

    A hand rests flat inside the open drum of a dryer to feel for warmth, the round door swung wide.
  4. 4

    Go on only if it is fully cold#

    Any warmth means the not-hot-enough steps apply instead. 1

Which cycles are meant to run without heat?#

Several are. Samsung's cycle guide describes Air Fluff as a cycle with no heat that tumbles the load in room-temperature air, and Wrinkle Prevent as turning the drum with no heat after a cycle finishes. Perm Press ends with a longer unheated cool-down. 4

A cool drum during Air Fluff, or in the last stretch of Perm Press, is the dryer doing its job. The same guide says Eco Dry is switched on by default for Normal and Time Dry on models that have it. 4 That default explains why the warmth test insists on turning it off first: left on, it can make a healthy dryer look cold in the opening minutes. 14

Steam cycles have their own caveat. Samsung's note at the top of the no-heat article says laundry may still be damp after a steam dry cycle, and that it should lie flat, hang, or finish on a different cycle. 14 Damp laundry after Steam says little about whether the heater works.

Has the dryer ever heated in this spot?#

If it has heated before and nothing about the setup has changed, you can skip the installation review. If it has never heated since installation, or the setup was recently altered, Samsung says installation is the probable cause and service may not be required. 1

The installation points the article lists are short. An electric dryer needs a 240-volt outlet, and a weak supply can let the panel and motor run while the heater sits idle. A gas dryer needs the gas line connected correctly and turned on. For electric models, inspect how the power cord was installed. And the exhaust vent has to meet the dryer's requirements. 1

Samsung adds that the user manual has the full details and that the company recommends professional installation. 1

Why would turning a breaker off and on help?#

An electric dryer runs on two circuits. They normally trip as a pair, but only one can trip, and then the dryer starts and spins without heat. Flip the breaker off, count to 30, then flip it on, and both circuits are confirmed live. 1

This is the one electrical step Samsung puts in the owner's hands, and it takes under a minute. Only operate the breaker you can identify, with dry hands, and keep the dryer's own door closed while you do it. If the breaker trips again when the dryer starts, stop there. That repeated trip belongs on your list of notes for a visit, not on a list of resets.

What does the vent have to do with no heat?#

Samsung dryers reduce heat when they detect that heat and moisture are not leaving, which guards against overheating in the vent. A badly blocked vent can therefore look like a failed heater. 1

That is why the path includes the vent blockage test, followed by vent cleaning and a requirements check. Our full vent blockage test walkthrough covers the buttons and each result. 12 For the vent, Samsung lists these requirements: sealed fittings with no gaps, a proper material (not plastic or foil), no more than the manual's maximum length, as few turns as possible because each 90-degree turn removes six feet of allowed length, and no kinks or flattening. 1

On a model without the test, Samsung's alternative is to disconnect the vent, run Time Dry with Eco Dry off for half a minute or longer, and compare the heat. If there is still none, the heating article applies. 2

Is weak heat the same problem?#

No, and Samsung keeps the two apart. When the drum feels at least a little warm, the article says service is almost never required and sends you to clean the lint filter, turn Eco Dry off, run the vent blockage test and check the vent's requirements. 1

It also says a failed heater usually means no heat at all, while a dryer that warms up yet drags on is most likely clogged somewhere in the vent. 1 So warmth in the drum is useful information: it moves the whole question from the heater to airflow, and it is worth telling us when you book.

What does a voltage code add to the picture?#

A voltage code such as 9C1 means something is abnormal in the supply reaching the dryer. Samsung asks you to confirm the dryer has its own circuit, is not on an extension cord, and, if it is electric, has a properly installed cord and the right voltage. 3

Two quirks are worth knowing. A model taken out of the country where it was sold can show the error because power grids differ. And on a washer and dryer stacked with a multi-control kit, the washer may report a 9C1 for the dryer if you touch the dryer controls within five seconds of switching the washer on; Samsung offers a software update through the SmartThings app for that case. 3

When is it a repair?#

After a vent blockage test that passes, a dryer that still does not heat at all is a repair, and Samsung's final step says so. The same applies if the cold drum persists after the correct outlet, cord, gas and breaker checks. 1

At that point you have already ruled out the causes that are cheap to fix, which is useful: a technician can start on the heating circuit, not on the outlet. Book a technician and share what you found. Our work is separate from Samsung's, and any dryer inside its Samsung warranty period should be repaired under that cover. Our dryer repair page explains what a visit includes.

What should I write down for the visit?#

A short list saves time. Note the model number, whether it is gas or electric, whether it ever heated, what the display showed, the result of the 30-second test, and whether the vent blockage test passed. 12

Add the vent's material and approximate length, and whether it has changed since the dryer was installed. If any breaker tripped, say so. Photos of the cord and the back of the dryer help too.

Sources#

  1. Clothes are not dry after using Samsung dryerSamsung Electronics America (official US support article, samsung.com/us) · Page meta date 2026-05-05; fetched 12.11.2026 · Section Dryer has no heat at all, steps 1 to 8
  2. Run a Vent Blockage test on your Samsung dryerSamsung Electronics America (official US support article, samsung.com/us) · Page meta date 2026-05-04; fetched 12.11.2026 · Section Check for a vent blockage on models without the test
  3. Samsung dryer displays an error codeSamsung Electronics America (official US support article, samsung.com/us) · Page meta date 2026-05-04; fetched 12.11.2026 · Entries Voltage errors and Vent Blockage test results
  4. Cycles, settings, and features on your Samsung dryerSamsung Electronics America (official US support article, samsung.com/us) · Page meta date 2026-04-03; fetched 12.11.2026 · Sections Dryer cycles and Dryer settings and features (Air Fluff, Perm Press, Wrinkle Prevent, Eco Dry)

Here to help

Good questions.
Clear answers.

Talk to our team
How do I know the dryer makes no heat at all?

Set Time Dry, turn Eco Dry off, start a cycle, and after half a minute open the door and put a hand in the drum. Any warmth means this is not a no-heat case; Samsung then points you to the not-hot-enough steps. [1]

Could one tripped breaker leave the drum turning but cold?

Yes. An electric dryer has two circuits, usually tripping together, but occasionally only one goes. Then the panel and motor run while the heater does not. A 30-second pause at the breaker, then power back on, checks this. [1]

Does a new or moved dryer change the advice?

Yes. If it has never heated in its current spot, or the installation was changed lately, Samsung says installation is the likely cause and service may not be needed. Read the outlet, cord, gas and vent points closely. [1]

Is Eco Dry a reason for no heat?

Only for part of a cycle. Samsung says Eco Dry runs portions, such as the start, without heat. The steps for a truly cold dryer apply when even a Time Dry check with Eco Dry off stays cold. [1]

When is no heat a repair?

When the outlet, breaker, installation and vent have all been ruled out, including a passed vent blockage test, and the drum is still cold. Samsung's last step in that article is to request service. [1]

Let’s take care of it.

Smart appliances still
need a steady hand.