What it means
C2 on a Samsung induction cooktop means the IGBT sensor is open or shorted while the burner is operating. Turn the cooktop off and restart.
Samsung cooktop C2 / Sensors
C2 on a Samsung induction cooktop means the IGBT sensor is open or shorted while the burner is operating. Turn the cooktop off and restart.
Also shown as C2
C2 on a Samsung induction cooktop means the IGBT sensor is open or shorted while the burner is operating. Turn the cooktop off and restart.
Turn the breaker off before you go under the cooktop; wiring is work for a technician.
C2 returns.
Your Samsung checks, remembered on this device

Compare the display with C2 one character at a time: Samsung writes it with a capital C and the digit 2.

Turn the cooktop off, then restart it.

If it continues, unplug the power cord for 30 seconds or more, then reconnect.

Write down which burner was on.
Tell us your model and the checks you have already run, then open your request from this spot.
Book a visitThis is a sketch, because the inside of a Samsung changes from model to model. Tap an outlined part for its photo and the matching check.

Component reference
C2 on a Samsung NZ30K7880U* or NZ30A3060UK induction cooktop reports that the IGBT sensor is open, or shorted, while a burner is operating.
Read the definitionFor C2, Samsung says the IGBT sensor is open, or short, while the burner is operating.
Read the supporting manualWith C2 showing, turn the cooktop off and restart it. If the problem continues, unplug the power cord for 30 seconds or more, then reconnect.
Read the supporting manualSafety with C2: A cooking zone can stay hot after it is switched off. Switch off at the breaker before going under the cooktop.
Read the supporting manualRead C2 as a capital C and the digit 2. No other Samsung induction cooktop row on this site uses those characters, so there is no near neighbor to mix it up with.
Read the supporting manualManufacturer document
Samsung Electronics America (official manual PDF, downloadcenter.samsung.com)
DG68-00823A-09, PDF created 10.12.2024; Warranty (U.S.A) printed on p34 / PDF p34
Manufacturer document
Samsung Electronics America (official manual PDF, downloadcenter.samsung.com)
DG68-01384A, PDF created 14.01.2025; US contact and warranty on p34 / PDF p32
Scope: NZ30A3060UK induction cooktops; NZ30K7880U* 30-inch induction cooktops (US model suffix NZ30K7880US). Source: Electric Cooktop User manual NZ30K7880U*; Electric Cooktop User manual NZ30A3060UK, checked November 2026.
Samsung says the IGBT sensor is open, or short, while the burner is operating.
The manual does not explain it; it names the sensor.
Read it as a capital C and the digit 2. Samsung's induction cooktop list has no other row with these characters.
Samsung says to contact a local service center if the problem is not fixed. Book a visit with us.
Samsung codes, symptoms, parts, house calls
The underlined u on a Samsung induction cooktop is a Pan Detection Error: the cookware is unsuitable (size, material, placement), so the pan will not heat. If not corrected the element turns off after 1 minute.
A Samsung electric cooktop unit that switches on and off is behaving normally, even on high, and does so more with an undersized pan or one with a curved base. A unit that will not hold a rolling boil usually points to the pan or low voltage. Use flat pans that match the unit and cover them with a lid.
C2 on a Samsung NZ30K7880U* or NZ30A3060UK induction cooktop reports that the IGBT sensor is open, or shorted, while a burner is operating. The manual prints the meaning and no steps. Book a technician with us if C2 returns.
Book a diagnostic for your exact model, carried out beside the appliance.
Office details, and the access notes to send us.