What it means
SF3 appears on Samsung's list of other washer errors as a System Error. Samsung gives the name only, with no specific steps. Power the washer off for 2 to 3 minutes, power it on and restart. Book a technician with us if it continues.
Samsung washer SF3 / Control board
SF3 appears on Samsung's list of other washer errors as a System Error. Samsung gives the name only, with no specific steps. Power the washer off for 2 to 3 minutes, power it on and restart. Book a technician with us if it continues.
Also shown as SF3
SF3 appears on Samsung's list of other washer errors as a System Error. Samsung gives the name only, with no specific steps. Power the washer off for 2 to 3 minutes, power it on and restart. Book a technician with us if it continues.
Before you look behind a panel, pull the plug and shut both water taps, and mop up any puddle you find.
SF3 returns after the power-off and restart.
Your Samsung checks, remembered on this device

Compare the display with SF3 one character at a time: Samsung writes it with a capital S, a capital F and the digit 3.

Turn the washer off and leave it for 2 to 3 minutes.

Turn it back on and restart the cycle.

Write down the exact characters; some strings start with a digit and some with a letter.
Tell us your model and the checks you have already run, then open your request from this spot.
Book a visit
This is a sketch, because the inside of a Samsung changes from model to model. Tap an outlined part for its photo and the matching check.
For SF3, Samsung lists it in "All other errors" as a System Error, and gives no specific steps for it, only the basic power-cycle steps.
Read the supporting manualWith SF3 showing, power the washer off for 2 to 3 minutes, power it back on and restart the cycle. If the code comes back, note what the washer was doing when it appeared.
Read the supporting manualSafety with SF3: Treat a repeating system error as a service matter. Unplug the washer before you open any panel, and do not bypass any part.
Read the supporting manual5F3 differs from SF3 only by a look-alike character, S against 5. Samsung lists both under System Error, so they carry the same meaning.
Read the supporting manualManufacturer document
Samsung Electronics America (official US support article, samsung.com/us)
page meta date 2026-06-09 (latest of three page dates: 2024-09-04, 2026-05-05, 2026-06-09); no printed revision / article
Scope: Samsung washers, all models unless the article notes otherwise. Source: Samsung washing machine information and error codes (Samsung US support article TSG10000997), checked November 2026. The entry used for SF3 is printed as: "IE, SF, 5F, SF1, SF2, SF3, 5F1, 5F2, 5F3, 1 SF - System Error" (TSG10000997, web article).
Samsung lists it in "All other errors" as a System Error, and gives no specific steps for it, only the basic power-cycle steps.
No. It is in the "All other errors" part of the list, where the basic power-off, power-on and restart steps apply.
5F3 differs from SF3 only by a look-alike character, S against 5. Samsung lists both under System Error, so they carry the same meaning.
Samsung says to request service if the error continues after the basic steps. Book a visit with us at that point.
Samsung's line for System Error prints 10 strings, and SF3 is number 6, right after SF2 and right before 5F1.
Samsung codes, symptoms, parts, house calls
IE appears on Samsung's list of other washer errors as a System Error. Samsung gives the name only, with no specific steps. Power the washer off for 2 to 3 minutes, power it on and restart. Book a technician with us if it continues.
Samsung says most washer leaks come from conditions you can correct: a damaged hose or o-ring, debris under the door gasket, a drain hose set too deep or too shallow, a dirty pump filter, too much detergent, or a washer that rests off level. Water dripping from the door after you open it is normal. A leak with the door closed is not.
Book a diagnostic for your exact model, carried out beside the appliance.
Office details, and the access notes to send us.