Samsung washer C6 / Information

Samsung washer
error C6

Washer / display referenceC6

C6 is Samsung's Calibration mode on a washer, not an error. It recalibrates weight detection, runs the drum back and forth for 1 to 3 minutes and ends by itself. The washer must be empty for it to calibrate.

Also shown as C6

Last reviewed

Washer / display referenceC6
Meaning
C6 is Samsung's Calibration mode on a washer, not an error. It recalibrates weight detection, runs the drum back and forth for 1 to 3 minutes and ends by itself. The washer must be empty for it to calibrate.
Who handles it
Information only
Related codes
Source
Samsung washing machine information and error codes

What Samsung washer C6 means.

What it means

C6 is Samsung's Calibration mode on a washer, not an error. It recalibrates weight detection, runs the drum back and forth for 1 to 3 minutes and ends by itself. The washer must be empty for it to calibrate.

What you can safely check

Before you look behind a panel, pull the plug and shut both water taps, and mop up any puddle you find.

When to call a technician

C6 remains lit once the calibration has run.

Your Samsung checks, remembered on this device

Safe checks, in order.

0 of 4 checks done
  1. Samsung washer C6: Front-load washer control panel with a round dial and three buttons, a small display showing lit segment marks, and a basket of folded towels on the counter.
    Illustration. Follow your model’s instructions.
    Before you begin

    Read the display

    Compare the display with C6 one character at a time: Samsung writes it with a capital C and the digit 6.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Empty the drum

    Calibration will not be correct with anything inside the washer.

  3. A washer control panel with a short code lit on the screen
    Illustration. Follow your model’s instructions.
    Check 3

    Let it run

    It rotates the drum back and forth for 1 to 3 minutes and ends by itself.

  4. Over a technician's shoulder, hands hold a tablet showing an empty checklist with boxes, a front-loading washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    See the manual

    Samsung refers to its installation article and your user manual for how to start Calibration mode.

Still showing C6?

Tell us your model and the checks you have already run, then open your request from this spot.

Book a visit

The control and its sensors.

Conceptual Washer sectionControl panelControl boardLevel sensorMotor wiring1234
  1. 1Control panel
  2. 2Control board
  3. 4Motor wiring

This is a sketch, because the inside of a Samsung changes from model to model. Tap an outlined part for its photo and the matching check.

A little more context.

What is a Samsung washer reporting with C6?

Samsung says Calibration mode recalibrates the washer's weight detection, which sets the water amount per cycle. It is usually done at the end of installation.

Read the supporting manual

What should I check before I book a visit?

Make sure the drum is empty, then let it run. If anything is inside, remove it and run Calibration mode again.

Read the supporting manual

Can the washer stay in use while this shows?

It is a normal mode. Keep hands and clothing away from the drum while it turns.

Read the supporting manual

How is C6 different from the codes near it?

Cb differs from C6 only by a look-alike character, 6 against b. Samsung lists both under Calibration mode, so they carry the same meaning.

Read the supporting manual

The manual behind the message.

Manufacturer document

Samsung washing machine information and error codes

Samsung Electronics America (official US support article, samsung.com/us)

page meta date 2026-06-09 (latest of three page dates: 2024-09-04, 2026-05-05, 2026-06-09); no printed revision / article

Scope: Samsung washers, all models unless the article notes otherwise. Source: Samsung washing machine information and error codes (Samsung US support article TSG10000997), checked November 2026. The entry used for C6 is printed as: "Cb, C6: Calibration mode" (TSG10000997, web article).

Here to help

Good questions.
Clear answers.

Talk to our team
What is a Samsung washer reporting with C6?

Samsung says Calibration mode recalibrates the washer's weight detection, which sets the water amount per cycle. It is usually done at the end of installation.

Why would a washer be in Calibration mode?

It is normally a step at the end of installation. Samsung also notes that running it can sometimes help a washer that stopped spinning after a drain problem is fixed.

Is C6 the same as Cb?

Cb differs from C6 only by a look-alike character, 6 against b. Samsung lists both under Calibration mode, so they carry the same meaning.

Do I need a visit for C6?

This is a mode, not a failure. Book a visit with us only if the washer stays stuck in it.

Let’s take care of it.

Smart appliances still
need a steady hand.