What it means
9E1 is Samsung's voltage error on a washer: an irregularity in the electrical supply. Confirm the washer is on its own circuit and not on an extension cord. Book a technician with us if the code continues.
Samsung washer 9E1 / Power supply
9E1 is Samsung's voltage error on a washer: an irregularity in the electrical supply. Confirm the washer is on its own circuit and not on an extension cord. Book a technician with us if the code continues.
Also shown as 9E1
9E1 is Samsung's voltage error on a washer: an irregularity in the electrical supply. Confirm the washer is on its own circuit and not on an extension cord. Book a technician with us if the code continues.
Before you look behind a panel, pull the plug and shut both water taps, and mop up any puddle you find.
9E1 returns while the circuit and plug are in order.
Your Samsung checks, remembered on this device

Compare the display with 9E1 one character at a time: Samsung writes it with the digit 9, a capital E and the digit 1.

The washer should be on its own circuit. Check whether the breaker has tripped.

Plug the washer directly into the wall outlet; extension cords and power strips are not recommended.

Think about whether the power went out, the plug was pulled, or the breaker tripped before the code appeared.
Tell us your model and the checks you have already run, then open your request from this spot.
Book a visit
This is a sketch, because the inside of a Samsung changes from model to model. Tap an outlined part for its photo and the matching check.
For 9E1, Samsung says there is an irregularity in the electrical current supplied to the washer. PF also appears after an outage, an unplug or a tripped breaker.
Read the supporting manualWith 9E1 showing, plug the washer straight into its own wall outlet circuit, with no extension cord or shared power strip, then try again.
Read the supporting manualSafety with 9E1: Do not open the cabinet or touch the outlet wiring yourself. If the outlet is hot, scorched or loose, stop using it and call an electrician.
Read the supporting manual8E1 (Mems Sensor Error) differs from 9E1 by a single character, and Samsung lists it as a separate entry for this washer. BE1 (Mems Sensor Error) differs from 9E1 by a single character, and Samsung lists it as a separate entry for this washer.
Read the supporting manualSamsung's dryer page lists 9E1 among its dryer Voltage errors (9C1, 9E, 2E, 9E1) and says something is abnormal with the voltage supplied to the dryer.
Read the supporting manualManufacturer document
Samsung Electronics America (official US support article, samsung.com/us)
page meta date 2026-06-09 (latest of three page dates: 2024-09-04, 2026-05-05, 2026-06-09); no printed revision / article
Manufacturer document
Samsung Electronics America (official US support article, samsung.com/us)
page meta date 2026-05-04; no printed revision / article
Scope: Samsung washers, all models unless the article notes otherwise. Source: Samsung washing machine information and error codes (Samsung US support article TSG10000997), checked November 2026. The entry used for 9E1 is printed as: "9C1, 9C2, PF, 3E*, 2E, 9E1, 9E2, UC, 19C1, 19C2: Voltage error" (TSG10000997, web article).
Samsung says there is an irregularity in the electrical current supplied to the washer. PF also appears after an outage, an unplug or a tripped breaker.
Samsung says models used outside their country of origin may display it because power grids and regulations vary between countries.
Samsung puts PF in the same voltage group. PF specifically also follows an outage, an unplug or a tripped breaker.
On a small display the 1 in 9E1 can be taken for I or l. Samsung's washer list has no row spelled that way, so 9E1 is the reading to look up.
Samsung lists 9E1 as a Voltage error on both appliances. For a dryer it adds a check of the power cord installation and the supplied voltage on electric models.
Samsung's line for Voltage error prints 10 strings, and 9E1 is number 6, right after 2E and right before 9E2.
Samsung codes, symptoms, parts, house calls
PF is Samsung's voltage error on a washer: an irregularity in the electrical supply. Confirm the washer is on its own circuit and not on an extension cord. Book a technician with us if the code continues.
Samsung says most washer leaks come from conditions you can correct: a damaged hose or o-ring, debris under the door gasket, a drain hose set too deep or too shallow, a dirty pump filter, too much detergent, or a washer that rests off level. Water dripping from the door after you open it is normal. A leak with the door closed is not.
Book a diagnostic for your exact model, carried out beside the appliance.
Office details, and the access notes to send us.