What it means
HE1 appears on Samsung's list of other washer errors as a Heater Error. Samsung gives the name only, with no specific steps. Power the washer off for 2 to 3 minutes, power it on and restart. Book a technician with us if it continues.
Samsung washer HE1 / Heating
HE1 appears on Samsung's list of other washer errors as a Heater Error. Samsung gives the name only, with no specific steps. Power the washer off for 2 to 3 minutes, power it on and restart. Book a technician with us if it continues.
Also shown as HE1
HE1 appears on Samsung's list of other washer errors as a Heater Error. Samsung gives the name only, with no specific steps. Power the washer off for 2 to 3 minutes, power it on and restart. Book a technician with us if it continues.
Before you look behind a panel, pull the plug and shut both water taps, and mop up any puddle you find.
HE1 returns after the power-off and restart.
Your Samsung checks, remembered on this device

Compare the display with HE1 one character at a time: Samsung writes it with a capital H, a capital E and the digit 1.

Turn the washer off and leave it for 2 to 3 minutes.

Turn it back on and restart the cycle.

Write down the cycle and temperature selected, and whether the water seemed to heat.
Tell us your model and the checks you have already run, then open your request from this spot.
Book a visitThis is a sketch, because the inside of a Samsung changes from model to model. Tap an outlined part for its photo and the matching check.
Samsung lists it in "All other errors" as a Heater Error, and gives no specific steps for it, only the basic power-cycle steps.
Read the supporting manualPower the washer off for 2 to 3 minutes, power it back on and restart the cycle. If the code comes back, note what the washer was doing when it appeared.
Read the supporting manualTreat a repeating heater error as a service matter. Unplug the washer before you open any panel, and do not bypass any part.
Read the supporting manual8E1 (Mems Sensor Error) differs from HE1 by a single character, and Samsung lists it as a separate entry for this washer. 9E1 (Voltage error) differs from HE1 by a single character, and Samsung lists it as a separate entry for this washer.
Read the supporting manualManufacturer document
Samsung Electronics America (official US support article, samsung.com/us)
page meta date 2026-06-09 (latest of three page dates: 2024-09-04, 2026-05-05, 2026-06-09); no printed revision / article
Scope: Samsung washers, all models unless the article notes otherwise. Source: Samsung washing machine information and error codes (Samsung US support article TSG10000997), checked November 2026. The entry used for HE1 is printed as: "HC, HE, HE1, Hr, 1 HC - Heater Error" (TSG10000997, web article).
Samsung lists it in "All other errors" as a Heater Error, and gives no specific steps for it, only the basic power-cycle steps.
No. It is in the "All other errors" part of the list, where the basic power-off, power-on and restart steps apply.
On a small display the 1 in HE1 can be taken for I or l. Samsung's washer list has no row spelled that way, so HE1 is the reading to look up.
Samsung says to request service if the error continues after the basic steps. Book a visit with us at that point.
Samsung codes, symptoms, parts, house calls
HC appears on Samsung's list of other washer errors as a Heater Error. Samsung gives the name only, with no specific steps. Power the washer off for 2 to 3 minutes, power it on and restart. Book a technician with us if it continues.
Samsung says most washer leaks come from conditions you can correct: a damaged hose or o-ring, debris under the door gasket, a drain hose set too deep or too shallow, a dirty pump filter, too much detergent, or a washer that rests off level. Water dripping from the door after you open it is normal. A leak with the door closed is not.
Book a diagnostic for your exact model, carried out beside the appliance.
Office details, and the access notes to send us.