What it means
C-F0 on a Samsung built-in wall oven occurs when communication between the Main and Sub PBA is interrupted. Press OFF and restart; disconnect power for at least 30 seconds if it persists.
Samsung oven C-F0 / Control board
C-F0 on a Samsung built-in wall oven occurs when communication between the Main and Sub PBA is interrupted. Press OFF and restart; disconnect power for at least 30 seconds if it persists.
Also shown as C-F0
C-F0 on a Samsung built-in wall oven occurs when communication between the Main and Sub PBA is interrupted. Press OFF and restart; disconnect power for at least 30 seconds if it persists.
Turn the breaker off before you go behind a panel; wiring is work for a technician.
C-F0 remains once power has been cut and restored.
Your Samsung checks, remembered on this device

Compare the display with C-F0 one character at a time: Samsung writes it with a capital C, a hyphen, a capital F and the digit 0.

Then restart.

At least 30 seconds.
If it persists.
Tell us your model and the checks you have already run, then open your request from this spot.
Book a visitThis is a sketch, because the inside of a Samsung changes from model to model. Tap an outlined part for its photo and the matching check.
For C-F0, both wall oven manuals say communication between the Main and Sub PBA (circuit board assemblies) is interrupted.
Read the supporting manualWith C-F0 showing, press OFF and restart the oven. If it persists, disconnect all power to the oven for at least 30 seconds and reconnect.
Read the supporting manualSafety with C-F0: Switch the oven off at its breaker before disconnecting power.
Read the supporting manualC-20 (oven sensor) differs from C-F0 by a single character, and Samsung lists it as a separate entry for this wall oven. C-30 (PCB sensor) differs from C-F0 by a single character, and Samsung lists it as a separate entry for this wall oven.
Read the supporting manualManufacturer document
Samsung Electronics America (official manual PDF, downloadcenter.samsung.com)
DG68-00856A-03, printed footer 2018-08-29; PDF modified 17.04.2019; carries Warranty (U.S.A) on the same page as the code table (p59) / PDF p58
Manufacturer document
Samsung Electronics America (official manual PDF, downloadcenter.samsung.com)
Samsung user manual PDF created 15.01.2026 (no printed revision code on the cover) / PDF p65
Scope: NV51**700D** built-in electric wall ovens (NV7000C series); NV51K7770D* built-in electric wall ovens. Source: Built-In Electric Wall Oven User manual NV51K7770D*; Built-In Electric Wall Oven User manual NV51**700D**, checked November 2026. The entry used for C-F0 is printed as: "Main and Sub PBA is interrupted." (NV51K7770D_AA_DG68-00856A-03_EN-MES-CFR, page 58).
Both wall oven manuals say communication between the Main and Sub PBA (circuit board assemblies) is interrupted.
A printed circuit board assembly. The manuals name a Main and a Sub one.
On a small display the 0 in C-F0 can be taken for O or o. Samsung's wall oven list has no row spelled that way, so C-F0 is the reading to look up.
The manuals say to call for service if the power reset does not solve it. Book a visit with us.
Samsung codes, symptoms, parts, house calls
C-d0 on a Samsung built-in wall oven means the control key is shorted for 1 minute. Wipe the buttons clean, dry any water on or around them, then switch the oven off and try again.
If food bakes or roasts poorly in a Samsung wall oven, the manual looks first at controls set incorrectly, a rack in the wrong place or not level, and wrong cookware. An oven that runs too hot or cold may need its thermistor adjusted in Settings, Adjust Temp. Low voltage can also slow broiling.
Book a diagnostic for your exact model, carried out beside the appliance.
Office details, and the access notes to send us.