Samsung dishwasher 9E / Water and drain

Samsung dishwasher
error 9E

Dishwasher / display reference

9E is Samsung's low water level error on a dishwasher: there is not enough water in it. Empty the dishwasher, add detergent and run a normal cycle. If it recurs, switch it off at the breaker and book a technician with us.

Also shown as 9E

Last reviewed

Dishwasher / display reference
Meaning
9E is Samsung's low water level error on a dishwasher: there is not enough water in it. Empty the dishwasher, add detergent and run a normal cycle. If it recurs, switch it off at the breaker and book a technician with us.
Who handles it
Check, then book
Related codes
Source
Samsung dishwasher is displaying an error code

What Samsung dishwasher 9E means.

What it means

9E is Samsung's low water level error on a dishwasher: there is not enough water in it. Empty the dishwasher, add detergent and run a normal cycle. If it recurs, switch it off at the breaker and book a technician with us.

What you can safely check

Cut power to the dishwasher at its breaker before you reach into the base or behind a panel, and clear up any standing water first.

When to call a technician

9E recurs after the normal cycle.

Your Samsung checks, remembered on this device

Safe checks, in order.

0 of 4 checks done
  1. Samsung dishwasher 9E: A gloved, wet hand lifts the cylindrical mesh filter out of the dishwasher sump, with a little water in the basin below and a spray arm lying aside.
    Illustration. Follow your model’s instructions.
    Before you begin

    Read the display

    Compare the display with 9E one character at a time: Samsung writes it with the digit 9 and a capital E.

  2. Dishwashers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Empty the dishwasher

    Remove dishes and racks that might block spray arms.

  3. A washer control panel with a short code lit on the screen
    Illustration. Follow your model’s instructions.
    Check 3

    Add detergent

    Put detergent in the dispenser.

  4. Over a technician's shoulder, hands hold a tablet showing an empty checklist with boxes, a front-loading washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Run a normal cycle

    Start a Normal cycle and see whether the code returns.

Still showing 9E?

Tell us your model and the checks you have already run, then open your request from this spot.

Book a visit

Where a leak is caught.

Conceptual dishwasher sectionTub seam / gasketBase panFloat switchInlet valve1234
  1. 1Tub seam / gasket
  2. 2Base pan
  3. 3Float switch
  4. 4Inlet valve

This is a sketch, because the inside of a Samsung changes from model to model. Tap an outlined part for its photo and the matching check.

A little more context.

What is a Samsung dishwasher reporting with 9E?

For 9E, Samsung says there is not enough water in the dishwasher. The printed steps are to empty it, add detergent and run a normal cycle.

Read the supporting manual

What should I check before I book a visit?

With 9E showing, empty the dishwasher, add detergent and run a normal cycle. Don't try to reset or clear the code before you troubleshoot it, Samsung warns; otherwise the cause stays and the code can return.

Read the supporting manual

Can the dishwasher stay in use while this shows?

Switch off at the breaker if the code recurs, and mop up spilled water before you walk by it.

Read the supporting manual

How is 9E different from the codes near it?

The same characters also appear on a dryer, where Samsung ties it to Voltage errors. Check which appliance you are standing in front of.

Read the supporting manual

The manual behind the message.

Manufacturer document

Samsung dishwasher is displaying an error code

Samsung Electronics America (official US support article, samsung.com/us)

page meta date 2026-05-01; no printed revision / article

Scope: Samsung dishwashers, all models unless the article notes otherwise. Source: Samsung dishwasher is displaying an error code (Samsung US support article TSG10004499), checked November 2026. The entry used for 9E is printed as: "9E - Low water level error" (TSG10004499, web article).

Here to help

Good questions.
Clear answers.

Talk to our team
What is a Samsung dishwasher reporting with 9E?

Samsung says there is not enough water in the dishwasher. The printed steps are to empty it, add detergent and run a normal cycle.

Should I clear the code first?

No. Samsung says to troubleshoot before you reset or clear a code, so the cause is addressed.

Does 9E mean the same on a dryer?

The same characters also appear on a dryer, where Samsung ties it to Voltage errors. Check which appliance you are standing in front of.

Do I need a visit for 9E?

If the error occurs again, Samsung says to switch off power at the breaker and request service. Book a visit with us.

Let’s take care of it.

Smart appliances still
need a steady hand.